Procurar Junta De Expansão Da Ponte Da Ponte Da Estrada, Junta De Expansão Tipo Dedo, Junta De Expansão De Ponte De Alta Qualidade no diretório Industry Directory, fabricante / fornecedor / Fábrica confiável a partir de China

Cesta de Consulta (0)
Página inicial > Lista de Produto > Série de juntas de expansão de ponte > Junta de Expansão Tipo Dedo > Junção de expansão de tipo de dedo de alta qualidade (Made in China)

Junção de expansão de tipo de dedo de alta qualidade (Made in China)

Informação básica

Modelo:  Movement 120mm

Descrição do produto

N ° de Modelo: Movement 120mm Mercados de Exportação: Global Urgente: Sim Transporte: em Paletes ou Madeira Origem: Hebei, China Certificado: ISO9000 Classificação: F-Wm Marca: JianFeng Especificação: As Drawing Requirements Código HS: 5522233 I \ n P: Você pode descrever a junta de expansão do tipo pente? \ N A: A junta de expansão do tipo pente é para adaptar-se à modernização do transporte rodoviário de alta velocidade, carga pesada, durabilidade, conforto e manutenção das características de conveniência, Tem funções à prova d'água, poeira, antiderrapantes, anti-corrosão, anti ruído e outras funções. \ N \ n \ n \ n \ n II \ n P: Quais são os requisitos técnicos do dispositivo de junta de expansão? \ N A : Os seguintes são os requisitos técnicos do dispositivo de junção de expansão:
1.Use neoprene rubber(that is,CR,suitable for temperature in 60 °C ~-25° C)or use the natural rubber(that is,NR,suitable for temperature in 60° C~ -40 °C) .
2. The  quality of steel in expansion joint device requirements in line with the provisions of GB374, GB012.Profiled steel,(that is,16MN or Q345) comply with the provisions of JT/T1591. 
\ n \ n \ n \ n \ n \ n III \ n Q: Como organizar o dispositivo de junção de expansão na construção da ponte? \ n A: O seguinte é o layout da junta de expansão da ponte:
1. The arrangement of the telescopic device should be based on the overall arrangement of the bridge and the geometry of the bridge.Such as longitudinal slope,cross slope,plan Curvature,bearing arrangement,the direction and measurement of three direction displacement.
 When the longitudinal horizontal displacement of the bridge expansion joint is less than 5mm and the vertical displacement is less than 0.5mm,there is no need to install the expansion device.Flexible and waterproof sealing material can be provided in the joint.
3.The curved bridge expansion device should be set on the radius of curvature.For the Modular expansion device,the maximum width between two middle or middle beam and side beam of the outer edge of the carriageway is less than 80mm.
4.The expansion device should not be set at the low point of the concave vertical curve of the bridge.
\ n \ n \ n \ n \ n \ n \ n \ n \ n IV \ n P: Quais são os requisitos de desempenho do dispositivo de junção de expansão do pente? \ n A:
items numerical value
Maximum horizontal frictional resistance of stretching or compressing (Kn /m) ≤5
The uniformity of deformation in tension or compression(mm)
Total variation of maximum deviation
e≤80±1.5
e>80±2.0
The maximum vertical deviation or distortion of the compression or stretch(mm) 0.3~0.5
\ n \ n \ n \ n \ n \ n \ n \ n V \ n P: Qual é o problema a ter em atenção sobre o método de instalação da junta de expansão da Highway Bridge? \ nA: Os seguintes assuntos devem ser atenção:
1,If you want install the expansion joints after the spread the road ,pave road at first to ensure the surface flat of the road,then slot road to install expansion joints.
2,When you are installing expansion joints,you should check pre embedded steel bar by the end of next seam.If you find a crack or break and improper position or clearance,you must take remedial measures.
3,Lance the oil layer of the road by using joint cutter to make joint  of bridge and take cleaning.Should pay attention to keep the road cut in good condition and no eating phenomenon.Timely removal of the surface of the concrete tank filler and asphalt concrete and chiseling groove after cutting the.This series of processes is very important,and it will affect the quality of concrete pouring.
4,In the first spot welding part of the pre embedded steel bars and anchor ring to fix its position temporarily.
\ n \ n \ n \ n \ n \ n \ n Informações de contato \ n Gerente de vendas: Miss Joyce \ n Telefone celular: + 86-15233296877 \ n Tel: 86-318-5106277 \ n Fax: 86- 0318-5106277 \ n Website: www.prolianz.com \ n Empresa: Hengshui Jianfeng Engenharia Rubber Co., LTD.D. \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n \ n

Grupo de Produto : Série de juntas de expansão de ponte > Junta de Expansão Tipo Dedo